วันอาทิตย์ที่ 12 มกราคม พ.ศ. 2557

Polymer Anion, โพลิเมอร์ประจุลบ

โพลิเมอร์ประจุลบ, โพลิเมอร์แอนไอออน, Polymer Anion, Anionic Polymer
โพลิเมอร์ประจุบวก โพลิเมอร์แคทไอออน, Polymer Cation, Cationic Polymer

กระบวนการโคแอกกูเลชันเป็นกระบวนการประสานคอลลอยด์ ซึ่งเป็นสารแขวนลอยขนาดเล็กที่ตกตะกอนได้ช้ามาก คอลลอยด์มีขนาดอนุภาคอยู่ในช่วง 0.1-1 นาโนเมตร ซึ่งไม่สามารถแยกตัวออกจากน้ำได้โดยวิธีตกตะกอนตามธรรมชาติเนื่องจากอนุภาคของคอลลอยด์มีขนาดเล็กเกินไป หลักการของกระบวนการโคแอกกูเลชัน คือ การเติมสารโคแอกกูแลนด์ (Coagulant) เช่น สารส้ม (Aluminium Sulfate Al2(SO4)3.18H2O) ลงไปในน้ำเสียทำให้คอลลอยด์หลายๆอนุภาคจับตัวกันเป็นกลุ่ม เรียกว่า ฟล็อก (Floc) จนมีน้ำหนักมากและสามารถตกตะกอนลงมาได้รวดเร็ว สารโคแอกกูแลนด์ทำหน้าที่เสมือนเป็นตัวประสานให้อนุภาคมารวมตัวกันเป็นฟล็อก ส่วนประกอบสำคัญของกระบวนการโคแอกกูเลชัน มี 2 ส่วน คือ ถังกวนเร็ว และถังกวนช้า ถังกวนเร็วเป็นที่เติมสารเคมีและเป็นทางเข้าของน้ำเสีย สารเคมีและน้ำเสียจะผสมกันทันทีอย่างรวดเร็วในถังนี้ ส่วนถังกวนช้า เป็นที่สำหรับกระบวนการสร้างฟล็อก (Flocculation) ที่เกิดจากการรวมตัวของอนุภาคคอลลอยด์ เพื่อส่งไปตกตะกอนในถังตกตะกอนซึ่งอยู่ตามหลังถังกวนช้า หรืออาจรวมอยู่ในถังเดียวกันกับถังกวนช้า อนุภาคคอลลอยด์ที่ไม่ถูกบำบัดโดยถังตกตะกอน จะถูกส่งต่อไปบำบัดในถังกรอง น้ำที่ออกจากถังกรองจึงมีความใสสูงมาก นอกจากนี้ยังสามารถเติมสารโคแอกกูแลนต์เอด (Coagulant Aid) เป็นสารเคมีประเภทโพลิอิเล็กโทรไลต์ (Polyelectrolyte) ซึ่งเป็นสารโพลิเมอร์ที่มีน้ำหนักโมเลกุลสูง โดยโคแอกกูแลนต์เอดทำหน้าที่เป็นสะพานเชื่อมระหว่างอนุภาค หรือฟล็อกให้เกิดเป็นฟล็อกขนาดใหญ่ และตกตะกอนได้ง่าย สารโพลิอิเล็กโตรไลต์ที่ใช้ในกระบวนการโคแอกกูเลชัน อยู่ 3 ประเภท ได้แก่
 1.โพลิเมอร์ประจุบวก (Cationic Polymer)
 2.โพลิเมอร์ประจุลบ (Anionic Polymer)
 3.โพลิเมอร์ที่ไม่มีประจุ (Non Ionic Polymer)

Polymer anion  is a very high molecular weight, This is often the most demanding polymer
high charge anionic polymer are used to application. Due to the high polymer demand
increase the efficiency of setting, clarification, and difficulty in removing the maximum amount
sludge thickening and sludge de-watering of water, proper polymer selection is critical. This product is approved for use by the EPA in the In all cases, floc development and de-watering clarification treatment of raw water for potable usage. rate must be evaluated.

Application Plant feed solution preparation
Primary clarification Viscosity will limit the practical solution strengths To increase the removal of suspended solid and BOD. of the dry polymers. The following are the maximum recommended strengths.
Solution may be prepared manually by using a low

Biological clarification speed mixer with relatively large blades must be
may be required to provide either used to mix the polymer in the tank. Product
improved settling rates or suspended solids capture. degradation will occur if high speed mixers are used.
Approximately 30 – 90 minutes of mixing is required
to properly prepare a feed solution. The mixer should

Sludge thickening then be turned off.
It  is used in sludge thickening.

As waste sludge very broadly in make up, extensive
testing may be required to choose the optimum product.

Available Packaging 25 kg/bag

สอบถามข้อมูลเพิ่มเติมได้ที่ ฝ่ายขาย
Thai Poly Chemicals Co., Ltd.
บริษัท ไทยโพลีเคมิคอล จำกัด
ที่อยู่36/5 ม.9  แขวง/ตำบลนาดี  เขต/อำเภอเมืองสมุทรสาคร  จังหวัดสมุทรสาคร รหัสไปรษณีย์74000
Tel.: 034854888, 034496284
Fax.: 034854899, 034496285
Mobile: 0824504888, 0800160016
Website : www.thaipolychemicals.com
Email1 : thaipolychemicals@hotmail.com
Email2 : info@thaipolychemicals.com



ไม่มีความคิดเห็น:

แสดงความคิดเห็น